Electrocoagulation of Disperse Dyebath Wastewater: Optimization of Process Variables and Sludge Production

Article information

J. Electrochem. Sci. Technol. 2021;12(1):82-91
Publication date (electronic) : 2021 January 19
doi : https://doi.org/10.33961/jecst.2020.00787
1Bursa Technical University, Faculty of Engineering and Natural Sciences, Department of Environmental Engineering, 16310 Bursa, Turkey
2Konya Technical University, Faculty of Engineering and Natural Sciences, Department of Environmental Engineering, 42003 Konya, Turkey
3KTO Karatay University, Engineering Faculty, Department of Civil Engineering, 42003 Konya, Turkey
*E-mail address: ahmet.aygun@btu.edu.tr
Received 2020 February 13; Accepted 2020 August 27.

Abstract

This study was conducted to investigate the effect of initial pH, current density, and electrolysis time on process performance in terms of decolorization and chemical oxygen demand (COD) removal from disperse dyebath wastewater (DDW) by mono-polar parallel laboratory scale electrocoagulation (EC) process. COD reduction of 51.3% and decolorization of 92.8% were obtained with operating cost of 0.19 €/m3 treated wastewater for Al-Al electrode pair, while 90.5% of decolorization and 49.2% of COD reduction were obtained with operating cost of 0.20 €/m3 treated wastewater for an Fe-Fe electrode pair. The amount of sludge production were highly related to type of the electrode materials. At the optimum conditions, the amount of sludge produced were 0.18 kg/m3 and 0.28 kg/m3 for Al-Al and Fe-Fe electrode pairs, respectively. High decolorization can be explained by the hydrophobic nature of the disperse dye, while limited COD removal was observed due to the high dissolved organic matter of the DDW based on auxiliary chemicals. Energy, electrode, and chemical consumptions and sludge handling were considered as major cost items to find a cost-effective and sustainable solution for EC. The contribution of each cost items on operating cost were determined as 10.0%, 51.1%, 30.5% and 8.4% for Al-Al, and they were also determined as 9.0%, 38.0%, 40.5% and 12.5% for Fe-Fe, respectively. COD reduction and decolorization were fitted to first-order kinetic rule.

1. Introduction

The textile sector generates colored wastewater that is heavily polluted with generally synthetic dyes, auxiliaries, and salts [1]. Thus, textile wastewater discharged into a freshwater environment has become crucial issue. Especially colored discharges have shown to cause toxic effects on aquatic flora and reduced light transmittance directly prevents photosynthetic activity [2].

Synthetic dyes are classified into azoic, reactive, disperse, direct, acid, basic, sulfur, mordant, and vat dyes based upon their chemical composition and the method of their application in the dyeing process [3]. The most common allergen dyes which adversely affects the immune system by penetrating through the skin are disperse ones characterized by lipophilic behavior and low molecular weights [4]. Concern arises, as many disperse dyes are made from known carcinogens such as azo and nitro-compounds [5]. Anthraquinone-based disperse dyestuffs are the most resistant ones to biological and chemical reduction due to their aromatic ring structure [6].

Disperse dyestuffs characterized by non-ionic small particles which have aqueous dispersions insoluble at room temperature and substantivity to hydrophobic fibers [7]. Thus, these dyes are suitable for dyeing of polyester, cellulose acetate, nylon and acrylic fibers [8]. Dyeing of polyester fibers is very difficult in normal conditions due to the high crystal-line structure of the fibers, the hydrophobic character and the absence of effective functional groups in which the dye molecules can form chemical bonds. Therefore, the dyeing process can be carried out at high temperatures (up to 130°C) for the fibers to be dyed efficiently [9]. Dye particles are stabilized with dispersing agents used as auxiliary chemicals. In order to avoid problems during the dyeing process with disperse dyestuffs, the pH of the flotte should be kept between 4.5 and 5.5 [10]. It is recommended to adjust the pH of the dyebath with organic acid (i.e. acetic acid) for better adsorption onto the fiber [11]. The quantity of dye lost in the discharged effluent is estimated to be around 10% for disperse dyes [12].

Biological methods, especially activated sludge, are preferred to treat textile wastewater; because they are generally cheap and capable to remove organic pollutants and dyes [13]. Disperse dyebath wastewater (DDW) cannot be readily bio-degraded, because the structures of most commercial dye compounds are generally complex and most of them are non-biodegradable [14]. The dyestuff and organic pollutants in textile wastewater can be effectively removed by conventional methods such as chemical coagulation [15], advanced oxidation [16] and adsorption [17], electrooxidation [18]; but, the operating cost of these treatment methods are relatively high. To treat non-biodegradable material in textile wastewater by conventional methods is required more chemicals and energy consumptions comparing to electrocoagulation (EC) proces. Therefore, EC process started to commonly used to treat wastewater containing textile dyes [1924]. EC used to overcome some problems caused by other treatment methods. Additionally, EC have some advantages such as less sludge production, small area requirement and low initial investment cost [2527].

Most of studies have been focused on treatment of synthetically prepared dye solution using lab-scale EC process in a batch mode. Based on previous studies, decolorization varies between 85–100% while COD reduction changed from 40% up to 80% at optimized operating conditions [28,29]. Initial pH, current density, current efficiency, electrode material (aluminum, iron or stainless steel), electrode connection type (monopolar parallel or serial, and bipolar-serial), electrolysis time, inner-electrode distance and temperature have been determined as important factors for process efficiency [3032]. Electrochemical, chemical and physical processes, which occur simultaneously or sequentially in the EC, complicate the description of the pollutant removal mechanism [33,34]. It is reported that EC is very efficient in treatment of wastewater containing dye with low energy consumption [25,35].

The management of sludges generated in treatment plants is of importance that they cannot be neglected when the treatment costs of treatment sludges are taken into consideration. The amount of monomeric and polymeric precipitates based on Al-Al and Fe-Fe electrode pairs differ due to the auxiliary chemicals used in the textile sector. Therefore, it is of great importance to determine the sludge amount generated from the EC process.

Traditionally, optimization has been carried out by monitoring the influence of one factor at a time on response to find the best solution [36]. Its major drawback is that it does not represent the interactive effects among the independent variables on response. At the same time, the one-factor optimization increases the number of experimental runs, which is often very expensive or highly time-consuming approach [37,38]. Response Surface Methodology (RSM) is a combination of mathematical and statistical methods to design the experiments, useful to improve and optimize the process performance [39]. RSM can be used to developed satisfactory relation between response and EC variables with a limited number of experiments [40] Analysis of variance (ANOVA) is a statistical method used to determine the significant effects of variables and goodness of fitted models [41].

Dye removal from the textile wastewaters by EC is widely studied; however, limited studies are available about the effect of dyeing auxiliaries (acetic acid and dispersing agent) on the process performance with the lowest cost. Therefore, the main aims of the study are (i) to determine optimum operating conditions with cost-effective approach using both Al-Al and Fe-Fe sacrificial electrode pairs to remove COD and decolarization for DDW consisting of the disperse dyes and dyeing auxiliaries, (ii) to predict the COD reduction and decolorization rates satisfactorily by kinetic assessment, and (iii) to reveal the relationship between electrode consumption and sludge production.

2. Materials and Methods

2.1 Synthetic and real industrial disperse dyebath wastewater (DDW)

Synthetic DDW was prepared on the basis of typical disperse dyeing recipe obtained from a local textile manufacturer using 120 mg/L disperse dyes (by mixing three dyes: 5 mg/L of Disperse Yellow 241 (STPRS YEL CE5G), 100 mg/L of Disperse Red 362 (STPRS PNK FBSM), and 15 mg/L of Disperse Blue (STPRS RBN CERN), 1.5 g/L dispersing agent and 1.5 g/L acetic acid. In addition, 1 g/L NaCl was added to reduce the energy cost by increasing conductivity and reducing the potential difference [19]. 10% of the disperse dyes and all of the dye auxiliaries were assumed to remain in the DDW. In order to verify the results obtained with synthetic wastewater, real wastewater was collected from the local textile manufacturer’s disperse dyebath effluent. Characterizations of synthetic and real disperse dyebath wastewater are presented in Table 1.

Characterization of synthetic and real disperse dyebath wastewater

2.2 Experimental procedure

The experimental setup used in this study has been described in our previous publication [42]. At the beginning of each run, NaOH was used to set the pH, and 200 rpm mixing rate in the EC reactor was kept constant throughout the batch experiment at room temperature. Then, the supernatant was collected from the EC and filtered using glass fiber filters (0.45 mm microspore) to find decolorization and COD reduction rate. Electrode consumption and the amount of genereted sludge were determined using the methods suggested by previous studies [28,43].

2.3 Response Surface Method

Design Expert software package, version 11.0.3 (Stat-Ease Inc., MN, USA) was used for the scheduling the experiments and data analysis. Design of Experiments (DoE) is a powerful technique to optimize process performance and it has been broadly implemented in process design and development. A three-factor and a five-level central composite design (CCD) consisting of 17 runs were conducted including three replicates at the center point (a= 0) for Al-Al and Fe-Fe electrode pair. The coded process variables at five levels between −1.68 and +1.68 at the actual ranges determined according to preliminary experimental studies and literature surveys and presented in Table 2.

Independent process variables and their ranges

In our study, the polynomial function including quadratic terms allows to predict the responses (COD removal (YCOD, %), decolorization (Y525 %) for Al-Al and Fe-Fe electrode pairs) based on the independent variables (X1, X2 and X3) at selected range. The experimental findings were evaluated by the analysis of variance (ANOVA) in the confidence level of 95%. Backward elimination procedure was used to exclude the non-significant terms (p value > 0.05).

2.4 Analytical Methods

All chemicals were of analytical grade obtained from Merck. Disperse dye auxiliary and dyestuffs were obtained from local manufacturer. Three wavelengths, 436 nm, 525 nm, and 620 nm, were chosen to determine the apparent color based on EN ISO 7887. Decolorization was only presented in terms of absorbance at 525 nm, because of the dominant wavelength was 525 nm for DDW. Closed reflux colorimetric method (SM 5220 C) was used for COD analysis. WTW 340i model pH meter was used to measure pH.

2.5 Operating Cost

Electricity, electrode material, and chemical consumption are considered to determine the operating cost by using followed equation (Eq. 1) for treatment of DDW:

(1) Operating Cost=α·CChemical+β·CElectricity+γ·CElectrode+η·CSludge

where CChemical is the chemical consumption (kg/m3), CElectricity is the electricity consumption (kWh/m3), CElectrode is the electrode consumption (kg/m3), and Csludge is the amount of generated sludge (kg/m3) were determined based on previous studies [44]. The unit prices for electrical energy, electrode materials (Al and Fe) and sodium hydroxide from Turkish market used in calculating the operating cost were 0.072 €/kWh, 1.65 €/Kg for Al electrode, 0.85 €/Kg for Fe electrode and 0.40 €/Kg, respectively. The cost of sludge handling was 0.09 €/Kg.

3. Results and Discussion

3.1 Prediction of model equations and statistical analysis

Initial pH, current density and electrolysis time which were determined as the most important operating parameters were optimized by using approximating functions based on the data given in literature (XXX). CCD were selected to reduce the number of experiments and to reveal the combined effect of the independent variables on process performance in terms of COD reduction and decolorization for both Al-Al and Fe-Fe electrode pair (Table 3).

Experimental planning and actual responses obtained in the experiments

The experimental results were analyzed by RSM. An empirical relationship expressed by a second-order polynomial equation between process variables and responses according the results. The fitted second-order models in terms of coded factors can be used to explain COD reduction and decolorization. The fitted models are given in Eq. 2 and for Al-Al electrode pair and Eq. 4 and 5 for Fe-Fe electrode pair:

Al electrode;

(2) YCR525nm=+91.52-4.54x1+3.11x2+3.23x3-4.09x12
(3) YCOD=+44.71-1.11x1+1.15x2+12.51x3-1.41x12-1.55x22-3.32x32

Fe electrode;

(4) YCR525nm=+89.74+1.31x1+1.41x2+11.70x3-2.53x1x2-4.10x12-5.00x32
(5) YCOD=+42.87-0.9306x1+1.34x2+12.90x3-1.68x12-1.32x22-3.78x32

The signs in front of the fitted model terms can be used to explain the type of effect (synergistic or antagonistic) on response. It was observed that, when the value of positive sign terms in models was increased, it leads to an increase in COD reduction and decolorization. The terms with negative signs have diminishing effect on response. The generated models for both of Al-Al and Fe-Fe electrode pair fitted very well to the actual results for treatment of DDW by EC. The model must be generated appropriately to avoid poor or ambiguous results [45]. After discarding the non-significant terms by backward elimination process at p<0.05, the fitted models were regenerated only with statistically significant terms and were tested by ANOVA (Table 4).

ANOVA results

Based on previous study, for a good fitting of experimental results with proposed models, R2 and AP should be at least 0.80 and 4, respectively [28]. Adjusted R2 indicates how well terms fit a curve or line but adjusts for the number of terms in a model. If the model contains a large number of non-significant terms, the R2adjusted value will be decrease. The value of R2adjusted is equal to or less than R2. In addition, the closeness of R2adjusted and Pred-R2 values (allowable value 0.2) is indicative of a statistically successful model [46]. Most of the CV values were less than 5% which represents great precision and reliability for our experimental results [47]. Based on descriptive statistics, generated models can be used to reveal the process behavior.

3.2 Effect of variables

It was determined that initial pH, current density and electrolysis time had remarkably effect on decolorization and COD reduction for Al-Al and Fe-Fe electrode pairs. All of them were statistically significant (p <0.005). 3D surface response plots (Fig. 1 for Fe-Fe electrode pair and Fig. 2 for Al-Al electrode pair) were prepared to estimate the effect of independent variables on COD reduction and decolorization. In each plot, two variables were demonstrated while the other one was kept at center point (a= 0).

Fig. 1

Profile of COD removal and decolorization for Fe-Fe electrode pair.

Fig. 2

Profile of COD removal and decolorization for Al-Al electrode pair.

EC is one of the methods frequently used to achieve the desired success in the treatment of textile wastewater. The optimum pH value determination is very important. pH controls the generation of monomeric and polymeric species which have different absorbing properties based on the electrode type in the aqueous solution. It was determined that COD removal efficiency increased up to 43% by increasing pH value to 5.8 and decolorization increased up to 90% when the pH value was increased to 6.8 for Fe-Fe electrode pair. The amount of flock generation related with current density and electrolysis time according to the Faraday law. Increased electrolysis period and current density resulted in increased COD reduction and decolorization.

When the operating cost was not considered, 52% COD reduction and 97% decolorization were obtained for Fe-Fe electrode pair at the highest current density (50 A/m2) and electrolysis time (15 min). Limited COD reduction can be explained by the fact that all COD in the DDW was dissolved. Disperse dyes can be treated with EC process at shorter electrolysis times and current densities due to their hydrophobic nature. Similarly, in a previous study with DDW without auxiliary chemicals, it was reported that decolorization was achieved within a short electrolysis time of 4.5 min [48]. Based on another study conducted with stainless steel electrodes, the electrolysis time of 10–15 minutes was sufficient for approximately 55% COD removal and 100% decolorization, with an optimum pH range of 5.5 to 9.5 [49]. In addition, it is reported that less chemical is used for disperse dyestuffs than reactive dyestuffs in chemical coagulation processes [20].

As seen in Fig. 2, to obtain highest COD reduction and decolorization for Al-Al electrode pair, pH should be in the range of 5.0–7.0 to form Al (OH)3 in solid form. Therefore, the initial pH value was very important. When the initial pH was increased from 5.0 to 8.0, there was no change in COD removal efficiency (≈45%), but a decrease in color removal. At the same time, similar to another studies, when aluminum electrode was used, COD and color removal efficiencies increased as electrolysis time and current density increased [50].

Design Expert software used for numerical optimization of the experimental conditions (independent variables) such as initial pH, current density and electrolysis time to maximize the COD removal efficiency and decolorization and to minimize the total operating costs included energy, electrode and chemical consumption and sludge handling based on the desirability functions. The goals for each independent variable were selected in the range as criteria, while the goal is to maximize the response variable in terms of COD removal efficiency and decolorization and is to minimize the total operating cost. Same weight and the same importance were selected both dependent and independent variables. For the Al-Al electrode pair, a current density of 20 A/m2, an electrolysis period of 15 minutes and an initial pH of 5.3 were determined as optimum operating conditions to achieve 92.8% decolorization and 51.3% COD removal efficiency with operating cost of 0.19 €/m3 treated wastewater. However, if the Fe-Fe electrode pair was used, a current density of 20 A/m2, an electrolysis period of 15 minutes and an initial pH of 6.20 were determined as optimum operating conditions to achieve 90.5% decolorization and 49.2% COD removal efficiency with operating cost of 0.20 €/m3 treated wastewater. Al-Al electrode pair are proved to be better than the Fe-Fe electrode pair in the present study.

At the optimum, cost items were determined as energy (0.269 kWh/m3 equal to 0.019 €/m3 for Al-Al electrode pair and 0.252 kWh/m3 0.018 €/m3 for Fe-Fe electrode pair), electrode (0.059 kg/m3 equal to 0.097 €/m3 for Al-Al electrode pair and 0.089 kg/m3 equal to 0.076 €/m3 for Fe-Fe electrode pair), chemical consumption (0.058 €/m3 for Al-Al electrode pair and 0.081 €/m3 for Fe-Fe electrode pair) and sludge handling (0.18 kg/m3 equal to 0.016 €/m3 for Al-Al electrode pair and 0.28 kg/m3 equal to 0.025 €/m3 for Fe-Fe electrode pair).

Eventually, total operating cost components included energy, electrode and chemical consumption and sludge handling were determined as 10.0%, 51.1%, 30.5% and 8.4% for Al-Al electrode pairs, and 9.0%, 38.0%, 40.5% and 12.5% for Fe-Fe electrode pairs, respectively. The results showed that there are significant differences between the contribution of cost items on total cost, even though the costs are relatively equal. Al-Al electrode pair gives better decolorization and COD reduction at lower pH. Based on our results, it is simply seen that operating cost items change mostly based on NaOH utilization to regulate inital pH due to the low pH of DDW which was neglected in many previous studies.

3.3 Verification of optimized conditions using synthetic and real DDW

The appropriateness of the predictive model equation was tested using optimal conditions to determine the optimal response values for synthetic DDW. The predicted COD and decloarization values were in close agreement with the experimental values (error <5%) and were found to be not significantly different using paired t-test [51]. In experimental studies were conducted with real wastewater, 93.0% of decolorization and 51.5% of COD reduction were obtained with sludge production of 185 mg/L for Al-Al electrode pair, while 92.2% of decolorization and 46.9% of COD reduction were obtained with sludge production of 276 mg/L for an Fe-Fe electrode pair. The current experimental results confirmed that the prediction models were of sufficient accuracy and precision in verification studies conducted with both synthetic and real wastewater.

3.4 Kinetic study

The treated samples were collected at 5-minute intervals to monitor changes in decolorization and COD reduction from the EC at the optimum operating condition for kinetic assessment. Kinetic evaluation of EC process using both Al-Al and Fe-Fe electrode pair indicated that COD removal and decolorization fitted fairly well the first-order kinetic rules (Eq. 1).

(1) Ct=C0·ek1·t

Where k1 is the first-order rate constant in 1/min, Ct is effluent COD (mg/L) or Color (1/cm), t is electrolysis time.

The removal rate can be obtained from the slope of straight line as a kinetic coefficient for COD reduction and decolorization. Decolorization rate constants were calculated as 0.21 1/min and 0.20 1/min for Al-Al and Fe-Fe electrode pair, respectively. Similarly, researchers reported that decolorization rate constant for textile dye increased from 0.26 1/min to 0.34 1/min by increased current density from 2.0 mA/cm2 to 4.5 mA/cm2 [19]. COD reduction has a lower kinetic constant compared to decolarization. The first order COD reduction rate constants were determined as 0.051 1/min and 0.047 1/min for Al-Al and Fe-Fe electrode pair, respectively. In another study conducted using real wastewater, COD reducation rate constants were 0.050 1/min, 0.026 1/min and 0.044 1/min for Fe-Fe, Al-Al and Al-Fe electrodes pairs, respectively [52]. These results show that electrode material has a significant effect on COD reduction rate.

3.5 Sludge Production

In electrocoagulation processes, coagulant is produced electrochemically. In this process, metal dissolution occurs in the anode in accordance with faraday laws, while water reduction in the cathode. The formation of polymeric and monomeric aluminum/iron compounds based on electrode materials can be explained by complex electrochemical reactions and solution pH [53]. Therefore, it is important to determine the relationship between sludge formation and actual electrode consumption. The relationship between electrode consumption and sludge production are illustrated in Fig. 3.

Fig. 3

The relationship between electrode consumption and sludge production.

The increase theoretical dissolution as a function of applied current and electrolysis time was confirmed by the measuring the amount of produced sluge. At the optimum condition, the amount of generated sludges were 0.18 kg/m3 (equal to 1.61 g/g of dye removed) and 0.28 kg/m3 (equal to 2.60 g/g of dye removed) for Al-Al and Fe-Fe electrode pairs, respectively. Similar results reported at previous studies [54]. Experimental studies have shown that there was the linear relationship between electrode loss and sludge production.

4. Conclusions

In this study, the process variables affecting COD removal and decolorization from DDW simulated by a batch-operated laboratory scale EC were optimized using RSM. The Al-Al electrode pair was proved to be better than Fe-Fe electrode pair as a sacrificial electrode material in terms of COD removal and decolorization with low operating cost. The results showed that there is a significant difference between the cost items, even though the operating costs are relatively equal for treatment of DDW. Although it has been neglected in many studies, the chemical cost required for pH regulation had a significant share in the total cost. In addition, it was obviously deductible that the decolorization was occurred more quickly than COD removal for both electrodes based on kinetic rate constants. Experimental studies reveal that the there was a linear relationship between electrode loss and sludge generation.

Acknowledgment

The authors thank Cagatay YUCE (Pisa Textile Factory) for supplying the disperse dyes and auxiliary chemicals. The present study is financially supported by Selçuk University Scientific Research Project (Project No: 09101026). This paper was derived from a part of a Ph.D. thesis fulfilled by A. Aygun.

References

1. Cirik K, Dursun N, Sahinkaya E, Cinar O. Bioresour Technol 2013;133:414–420.
2. Tsantaki E, Velegraki T, Katsaounis A, Mantzavinos D. J Hazard Mater 2012;207–208:91–96.
3. Akar ST, Gorgulu A, Kaynak Z, Anilan B, Akar T. Chem Eng J 2009;148(1):26–34.
4. Meinke M, Abdollahnia M, Gähr F, Platzek T, Sterry W, Lademann J. Exp Dermatol 2009;18(9):789–792.
5. Faraco V, Pezzella C, Giardina P, Piscitelli A, Vanhulle S, Sannia G. J Chem Technol Biotechnol 2009;84(3):414–419.
6. Robinson T, McMullan G, Marchant R, Nigam P. Bioresour Technol 2001;77(3):247–255.
7. Yang D, Li H, Qin Y, Zhong R, Bai M, Qiu XQ. J Dispers Sci Technol 2015;36(4):532–539.
8. Ujhelyiova A, Bolhova E, Oravkinova J, Tiňo R, Marcinčin A. Dye Pigment 2007;72(2):212–216.
9. Altun S. Color Technol 2005;121(2):69–71.
10. Lee JJ, Lee WJ, Kim JP. Fibers Polym 2003;4(2):66–70.
11. Akrman J, Přikryl J. J Appl Polym Sci 1997;66(3):543–550.
12. Burkinshaw SM, Salihu G. Dye Pigment 2013;99(3):548–560.
13. Alaton IA, Insel G, Eremektar G, Babuna FG, Orhon D. Chemosphere 2006;62(9):1549–1557.
14. Sarayu K, Sandhya S. Appl Biochem Biotechnol 2012;167(3):645–661.
15. Arslan I. J Hazard Mater 2001;85(3):229–241.
16. Karatas M, Argun YA, Argun ME. J Ind Eng Chem 2012;18(3):1058–1062.
17. Anastopoulos I, Hosseini-Bandegharaei A, Fu J, Mitropoulos AC, Kyzas GZ. J Dispers Sci Technol 2018;39(6):836–847.
18. Sahinkaya S. J Ind Eng Chem 2013;19(2):601–605.
19. Kim TH, Park C, Shin EB, Kim S. Desalination 2002;150(2):165–175.
20. Merzouk B, Gourich B, Madani K, Vial C, Sekki A. Desalination 2011;272(1–3):246–253.
21. Phalakornkule C, Polgumhang S, Tongdaung W, Karakat B, Nuyut T. J Environ Manage 2010;91(4):918–926.
22. Nandi BK, Patel S. J Dispers Sci Technol 2013;34(12):1713–1724.
23. Ilhan F, Ulucan-Altuntas K, Dogan C, Kurt U. Global NEST J 2019;21(2):187–194.
24. Bener S, Bulca O, Palas B, Tekin G, Atalay S, Ersoz G. Process Saf Environ Prot 2019;129:47–54.
25. Bayramoglu M, Kobya M, Can OT, Sozbir M. Sep Purif Technol 2004;37(2):117–125.
26. Dimoglo A, Sevim-Elibol P, Dinc O, Gokmen K, Erdogan H. J Water Process Eng 2019;31:100877.
27. Gunawan D, Kuswadi VB, Sapei L, Riadi L. Environ Eng Res 2018;23(1):114–119.
28. Arslan-Alaton I, Kobya M, Akyol A, Bayramoǧlu M. Color Technol 2009;125(4):234–241.
29. Daneshvar N, Oladegaragoze A, Djafarzadeh N. J Hazard Mater 2006;129(1–3):116–122.
30. Naje AS, Chelliapan S, Zakaria Z, Abbas SA. J Environ Manage 2016;176:34–44.
31. Keyikoglu R, Can OT, Aygun A, Tek A. Colloids Interface Sci Commun 2019;33:100210.
32. Hossain MM, Mahmud MI, Parvez MS, Cho HM. Environ Eng Res 2013;18(3):157–161.
33. Alinsafi A, Khemis M, Pons MN, Leclerc JP, Yaacoubi A, Benhammou A, Nejmeddine A. Chem Eng Process Process Intensif 2005;44(4):461–470.
34. Hakizimana JN, Gourich B, Chafi M, Stiriba Y, Vial C, Drogui P, Naja J. Desalination 2017;404:1–21.
35. Assémian AS, Kouassi KE, Drogui P, Adouby K, Boa D. Water Air Soil Pollut 2018;229(6):184.
36. Gul O, Atalar I, Saricaoglu FT, Yazici F. J Food Process Preserv 2018;42(5):e13615.
37. Nourouzi MM, Chuah TG, Choong TSY. Water Sci Technol 2011;63(5):984–995.
38. Tetteh EK, Naidoo DB, Rathilal S. Eng Res 2019;24(4)
39. Sharma S, Aygun A, Simsek H. Chemosphere 2020;249:126511.
40. Sharma S, Simsek H. Chemosphere 2019;221:630–639.
41. Mook WT, Aroua MK, Szlachta M, Lee CS. Water Sci Technol 2017;75(4):952–962.
42. Aygun A, Nas B, Sevimli MF. Korean J Chem Eng 2019;36(9):1441–1449.
43. Yavuz Y, Ogutveren B. J Environ Manage 2018;207:151–158.
44. Demirbas E, Kobya M. Process Saf Environ 2017;105:79–90.
45. Olmez T. J Hazard Mater 2009;162(2–3):1371–1378.
46. Aygun A, Dogan S, Argun ME, Ates H. Environ Eng Res 2019;24(1):24–30.
47. Gengec E, Kobya M, Demirbas E, Akyol A, Oktor K. Water Sci Technol 2012;65(12):2183–2190.
48. Lemlikchi W, Khaldi S, Mecherri MO, Lounici H, Drouiche N. Sep Sci Technol 2012;47(11):1682–1688.
49. Arslan-Alaton I, Turkoglu GG. Environ Eng Sci 2008;25(3):295–307.
50. Kabdasli I, Vardar B, Arslan-Alaton I, Tunay O. Chem Eng J 2009;148(1):89–96.
51. Hossain MB, Brunton NP, Patras A, Tiwari B, O’Donnell CP, Martin-Diana AB, Barry-Ryan C. Ultrason Sonochem 2012;19(3):582–590.
52. Linares-Hernández I, Barrera-Díaz C, Roa-Morales G, Bilyeu B, Ureña-Núñez F. Chem Eng J 2009;148(1):97–105.
53. Khosravi R, Hazrati S, Fazlzadeh M. Desalin Water Treat 2016;57(31):14656–14664.
54. Nandi BK, Patel S. Arab J Chem 2017;10:S2961–S2968.

Article information Continued

Fig. 1

Profile of COD removal and decolorization for Fe-Fe electrode pair.

Fig. 2

Profile of COD removal and decolorization for Al-Al electrode pair.

Fig. 3

The relationship between electrode consumption and sludge production.

Table 1

Characterization of synthetic and real disperse dyebath wastewater

Parameter Unit Synthetic Real

Value SD (±) Value SD (±)
Color 436 nm cm−1 0.459 0.03 0.543 0.04
525 nm cm−1 0.958 0.05 0.830 0.06
620 nm cm−1 0.327 0.03 0.417 0.03
COD mg/L 3530 93 3200 85
pH - 3.37 0.1 3.45 0.1

Table 2

Independent process variables and their ranges

Variables Unit Range
Initial pH (X1) - 4.0 – 9.0
Current density (X2) A/m2 9.8 – 60.2
Electrolysis time (X3) min 1.6 – 18.4

Table 3

Experimental planning and actual responses obtained in the experiments

Run Variables Responses

Al-Al electrode pair Fe-Fe electrode pair

X1 X2 X3 CR λ525 (%) COD (%) CEnergy (€/m3) CElectrode (€/m3) CChemical (€/m3) CSludge (€/m3) Total Cost (€/m3) CR λ525 (%) COD (%) CEnergy (€/m3) CElectrode (€/m3) CChemical (€/m3) CSludge (€/m3) Total Cost (€/m3)
1 6.5 35.0 10.0 92.38 43.2 0.04 0.08 0.09 0.03 0.23 89.25 44.2 0.04 0.09 0.09 0.05 0.26
2 6.5 60.2 10.0 96.24 42.5 0.13 0.13 0.09 0.05 0.39 92.38 42.7 0.11 0.15 0.09 0.07 0.43
3 6.5 35.0 1.6 80.38 15.7 0.01 0.02 0.09 0.02 0.13 55.44 10.7 0.01 0.02 0.09 0.01 0.13
4 5.0 20.0 5.0 87.37 25.8 0.01 0.02 0.07 0.02 0.12 64.10 22.6 0.01 0.03 0.07 0.02 0.12
5 3.9 35.0 10.0 88.20 41.3 0.04 0.09 0.03 0.03 0.18 71.82 38.2 0.04 0.09 0.03 0.04 0.20
6 6.0 35.0 10.0 94.26 45.5 0.04 0.08 0.09 0.02 0.23 89.35 42.3 0.04 0.09 0.09 0.04 0.26
7 8.0 50.0 15.0 86.12 48.4 0.15 0.17 0.12 0.05 0.48 91.34 46.4 0.14 0.20 0.12 0.10 0.55
8 5.0 50.0 15.0 99.79 55.2 0.15 0.15 0.07 0.05 0.42 98.23 52.2 0.14 0.20 0.07 0.10 0.50
9 8.0 20.0 5.0 79.65 21.2 0.01 0.03 0.12 0.02 0.17 74.74 20.9 0.01 0.03 0.12 0.02 0.17
10 5.0 50.0 5.0 90.08 28.1 0.05 0.05 0.07 0.02 0.19 71.19 25.7 0.05 0.07 0.07 0.03 0.21
11 5.0 20.0 15.0 89.25 51.5 0.02 0.08 0.07 0.03 0.20 91.44 50.4 0.02 0.08 0.07 0.03 0.20
12 6.5 35.0 18.4 98.85 54.6 0.07 0.14 0.09 0.05 0.35 94.57 53.2 0.06 0.17 0.09 0.08 0.40
13 6.5 35.0 10.0 94.05 45.5 0.04 0.08 0.09 0.02 0.23 91.34 42.2 0.04 0.09 0.09 0.04 0.25
14 8.0 50.0 5.0 85.18 26.5 0.05 0.06 0.11 0.02 0.24 67.22 23.5 0.05 0.07 0.11 0.03 0.26
15 9.0 35.0 10.0 72.34 39.8 0.04 0.08 0.12 0.02 0.26 83.30 37.6 0.04 0.09 0.12 0.04 0.29
16 6.5 9.8 10.0 85.70 37.8 0.01 0.03 0.09 0.02 0.14 85.39 35.1 0.01 0.03 0.09 0.02 0.14
17 8.0 20.0 15.0 80.17 51.9 0.02 0.07 0.11 0.02 0.22 90.18 48.4 0.02 0.08 0.11 0.05 0.25

CR l525 : Color removal at 525 nm

Table 4

ANOVA results

Response Elc. R2 R2adj Pred-R2 SD CV PRESS F-value Prob>F AP
CR λ525 (%) Al 0.88 0.85 0.78 2.91 3.29 195.14 22.92 <0.0001 16.50
COD (%) 0.98 0.97 0.95 1.98 5.00 116.03 97.47 <0.0001 33.06
CEnergy(€/m3) 0.98 0.97 0.94 0.008 15.74 0.0019 148.22 <0.0001 33.53
CElectrode (€/m3) 0.99 0.99 0.98 0.005 6.13 0.0008 282.83 <0.0001 52.66
CChemical (€/m3) 0.94 0.93 0.89 0.0062 7.08 0.0010 226.78 <0.0001 39.96
Total Cost (€/m3) 0.98 0.97 0.92 0.018 8.09 0.0109 74.82 <0.0001 27.93
CR 525 (%) Fe 0.96 0.94 0.85 3.17 3.85 367.24 39.62 <0.0001 19.32
COD (%) 0.99 0.98 0.96 1.65 4.42 94.67 150.78 <0.0001 40.89
CEnergy(€/m3) 0.94 0.93 0.90 0.012 26.05 0.0032 67.63 <0.0001 24.52
CElectrode (€/m3) 0.99 0.99 0.99 0.0021 2.25 0.0001 4000 <0.0001 178.3
CChemical (€/m3) 0.94 0.93 0.89 0.0062 7.08 0.0010 226.78 <0.0001 39.96
Total Cost (€/m3) 0.98 0.97 0.93 0.0185 8.21 0.0123 79.10 <0.0001 28.43

AP: Adequate Precision, CV: Coefficient of Variance, PRESS: Predicted Residual Error sum of squares, SD: Standard Deviation